Outlines
Every outline run type in Ember and what each of its settings does.
Outlines
When a shape’s stitch type is set to Outlined, its stitch output is controlled by the run type. Pick a run type in Shape Settings, then use the run settings underneath to fine-tune how that outline stitches.
Single
A single run is the simplest outline: one pass of stitches that follows your path. It’s great for construction lines, light borders, and anything that shouldn’t look heavy.
Stitch Length
How long each stitch is along the path, in millimeters. Shorter stitches hug curves more tightly and look denser; longer stitches cover distance faster and look more open.
Triple
A triple run travels the path forward, back, and forward again. You get a thicker, more durable line than a single run without jumping up to a full satin column — useful for bold outlines that still need to stay relatively thin.
Stitch Length
Same idea as single run: the length of each stitch along the path, in millimeters.
Satin
Satin lays stitches side-to-side across a column that follows your path, creating a smooth, filled border. It’s the go-to for patch edges, thick lettering outlines, and anywhere you want a polished, solid look.
Width
How wide the satin column is, in millimeters. Wider satin covers more fabric and looks bolder; narrower satin stays crisp on finer details.
Density
The spacing between stitches across the satin column, in millimeters. Lower values pack stitches tighter (heavier coverage, more thread); higher values open the satin up.
Split Satin
When enabled, wide satin columns are automatically split into multiple narrower columns so stitches don’t get impractically long which could lead to snags, loose stitches, or even errors when the machine is embroidering. Turn this off if you specifically want one unbroken column.
Max Width
Only available when Split Satin is on. The widest a single satin column is allowed to get before Ember splits it, in millimeters.
Stagger
Only available when Split Satin is on. When enabled, the seams between split columns are offset along the path so they don’t form one continuous ridge.
Underlays
Satin supports one or more underlays stitched before the top satin. Underlays stabilize the fabric and help the satin sit smoothly. You can add, remove, and configure multiple underlays.
Each underlay has a type:
- Center — a run down the middle of the column. Settings: Length (underlay stitch length in mm).
- Contour — a run that follows the edges of the column. Settings: Length, Inset (how far in from the edge, in mm), and Cap Inset (how far the ends pull in, in mm).
- Zig Zag — a zigzag that fills under the satin. Settings: Length, Density (zigzag spacing in mm), Inset, and Cap Inset.
E Stitch
E Stitch builds an “E”-shaped embroidery edge along your path — a stem run with perpendicular “teeth” sticking out. It’s commonly used for appliqué edges and decorative borders. Sometimes referred to as a "blanket stitch."
Stitch Length
The length of stitches along the stem of the E, in millimeters.
Width
How far the E teeth stick out from the path, in millimeters.
Flipped
Mirrors the E pattern to the other side of the path. Useful when you need the teeth facing inward or outward relative to a shape.
Double Rope Run
A decorative double rope that twists along your path as two interlaced runs. Good for ornamental borders and accent lines.
Stitch Length
How long each stitch is along the rope, in millimeters.
Width
How wide the rope is overall, in millimeters. Wider values exaggerate the twist; narrower values keep it tighter to the path.
Triple Rope Run
Like Double Rope Run, but with three interlaced strands for a fuller twisted look.
Stitch Length
How long each stitch is along the rope, in millimeters.
Width
How wide the rope is overall, in millimeters.
Manual
Manual outlines don’t generate a stitch pattern from settings — you’re in control of the stitches yourself. There are no run settings for Manual.